ENSONIQ TS-10 Specifications download pdf (Page 32)

Section 1 — Controls and Basic Functions TS-10 Musician’s Manual

functions. When a single foot switch is connected, set the left foot switch to *UNUSED* on the

System sub-page. For more information about assigning the foot switches, refer to Section 2 —

System Page Parameters.

Note: If you are using a single foot switch (SW-2 or SW-6) in either of the Foot Switch

jacks, the FOOT-SW1-L and/or SW2-L values on the System page should always be set

to *UNUSED*. This will prevent note drones. Remember that the Foot Switch jacks

are optimized for use with a stereo Foot Switch (SW-10), and when a single foot switch

is connected, it behaves like the right foot switch.

6) Pedal•CV

This jack is for connecting an optional ENSONIQ Model CVP-1 Control Voltage Foot Pedal,

which is assignable as a modulator to various parameters within the TS-10. The pedal gives you

a handy alternative modulation source when, for example, you would want to use the Mod

Wheel but both hands are busy.

A CV pedal plugged into this jack can also act a volume pedal,

controlling the volume of the currently selected sound(s). A

parameter on the System page (press System, then underline

PEDAL=VOL/MOD), determines whether the CV pedal will act as a

modulator or as a volume pedal. Set to PEDAL=VOL to use the CV

pedal to control volume.

Pedal/CV Specs: 3-conductor (Tip= control voltage input, Ring=510

ohm resistor to +5 Volts, Sleeve= ground). 36 KOhm input

impedance, DC coupled. Input voltage range=0 to 3 volts DC. Scan

rate=32mS (maximum recommended modulation input= 15 Hz). For

use with an external control voltage, use a 2-conductor cable with the

voltage on the tip and the sleeve grounded.

7) AUX Out Right/Mono

8) AUX Out Left/Mono

The AUX Outputs provide an additional stereo output for use in mixing down sequences, etc.

The AUX Outputs contain the dry (no effects) signal only, allowing you to process and mix

certain sounds separately. TS-10 sounds can be routed to the AUX Outputs from the Track

Effects page, or individual voices can be set to the AUX Outputs from the Output page. When

using the AUX Outputs in stereo, connect these outputs to two separate channels of your mixer

and pan them left and right. If you want to have a mono AUX Output, make sure that only one

of the AUX Out jacks is connected.

9) Main Out — Right/Mono

10) Main Out — Left/Mono

The Main Out jacks contain the wet (effected) output of the TS-10’s effects processor. Any sounds

or individual voices routed to FX1, FX2, or DRY will be routed to the Main Outs. To operate the

TS-10 in stereo, connect these outputs to two discrete channels of your mixer and pan them left

and right. Note that either of the Main Outs can be used as a mono output. If you want to listen

to the main output in mono, make sure that only one of the Main Out jacks is connected.

11) Phones

To listen to the TS-10 in stereo through headphones, plug the phones into this jack. The Phones

output contains a mix of the signal from the Main Outputs and the AUX Outputs. Headphone

volume is controlled by the Volume Slider on the front panel. Note that plugging headphones

into this jack does not automatically turn off the audio in the Main or AUX Outputs.

ENSONIQ

CVP-1

Control Voltage Foot Pedal

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 371 372

Comments to this Manuals

No comments

ENSONIQ TS-10 Specifications Page 32

Comments to this Manuals

Related products and manuals for Synthesizer ENSONIQ TS-10